search

Dji Z15-5D III (HD) User Manual Page 14

  • Download
  • Add to my manuals
  • Print
  • Page
    / 28
  • Table of contents
  • TROUBLESHOOTING
    •
  • BOOKMARKS
    • Rated. / 5. Based on customer reviews
Page view 13
Zenmuse Z15-5D III
(
HD
)
User Manual
14
©
2014 DJI. All Rights Reserved.
GCU Wiring
GCU Wiring
WooKong-M users can connect the GCU to any spare CAN-Bus port on the ight control system by using a
CAN-Bus cable.
A2 users should connect the GCU to the port labeled CAN1. Alternatively, you may connect the GCU to the
CAN port located on any modules that are already connected to the A2’s CAN1 port via a CAN-Bus cable.
Camera
HDMI
HDMI signal
HDMI-HD/AV cable
HD/AVsignal
Monitor
Input
5D III(HD)
Gimbal
7-Pin cable
Self-prepared by user
Wireless video
transmission module
Wireless video
transmission module
Air unit
Wireless signal
5.8G/2.4G/1.2G
Ground unit
10-Pinto 9-Pin cable
HD/AVsignal HD/AVsignal
GCU
G9 G7
This example is based on a Z15-5D III (HD) gimbal and the A2 ight control system.
1. Connect the Gimbal Port on the Lightbridge Air System to the G7 port on the Z15-5D III (HD) GCU using
the supplied HD video power cable (7-pin cable).
2. Connect the DBUS port on the Lightbridge Air System to the DBUS port (X2 port) on the A2 ight control
system. Toggle the HD/AV switch to the HD position.
3. Refer to the Lightbridge and A2 ight control system manuals to complete the connection.
The HD video power cable is included with the Z15-5D III (HD) gimbal. To transmit gimbal and
aircraft signals, connect the RC receiver to the DJI Lightbridge ground system when connecting the
GCU.
Always connect the wireless video transmission module to the GCU before powering on.
A standard HD video power cable (7-pin cable) is recommended.
Complete the other connections according to the Lightbridge user manual.
If the gimbal LED indicator blinks red continuously, please power cycle the gimbal. (Power it off,
then power it back on)
If the video signal does not transmit, check each step.
The following diagram shows how a video signal is transmitted from the gimbal.
GCU Wiring
Page view 13
1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 27 28

Comments to this Manuals

No comments
Related products and manuals for Hardware Dji Z15-5D III (HD)
Hardware Dji Z15-5D User Manual   (24 pages)
Hardware Dji Z15-GH4 (HD User Manual   (28 pages)
Hardware Dji Z15-GH3 User Manual   (26 pages)
Hardware Dji Z15 User Manual   (33 pages)
Hardware Dji H3-3D User Manua User Manual   (20 pages)
Hardware Dji H3-3D Anti-interference Reinforcement Board User Manual   (1 pages)
Hardware Dji H3-2D User Manual   (16 pages)
Hardware Dji H3-2D User Manual   (17 pages)
Hardware Dji H3-2D User Manual   (19 pages)
Hardware Dji Ronin User Manual   (21 pages)
Hardware Dji iOSD MARK II User Manual   (17 pages)
Hardware Dji iOSD mini User Manual   (5 pages)
Hardware Dji E300 User Manual   (4 pages)
Hardware Dji DR16 User Manual   (4 pages)
Hardware Dji E600 User Manual   (4 pages)
  • Water Furnace Colibri ION Audio U.S. Ceramic Tile AKTRONIX
  • BMW Unknown Brother Label printers Microsoft Mice Interquartz Telephones Hitachi Power adapters & inverters
  • Acer XB272 Samsung 460P Sony VGX-XL1 Samsung NP670Z5E Gorenje ECT 2600 P2
  • Htc Incredible S User Manual Dell PowerEdge R730xd User Manual Vertex-standard FT-60R User Manual Pioneer AVIC-HD3-II User Manual Summit GC424BGL User Manual